MinutesofThunder

Your Complete RC Technology Hub

FPV Latency Calculator

Pick a video system, or build one from a camera, transmitter, and goggles, then enter the car's speed. The result is typical glass-to-glass delay and how far the chassis travels before the picture updates.

Video system

Or add up each stage

Use this when a custom measurement is available. Camera-only and goggle-only figures from different tests often should not be added as if they were one lab result. System presets above use end-to-end numbers instead.

* The 29 ms box-goggle figure is from a similar model (Cobra X), not a dedicated EV800D test.

Figures are typical published values, not a lab test of one specific board or firmware. Real latency varies with camera, goggles, mode, firmware, and signal quality.

--
Glass-to-glass latency
--
Distance during delay
--
Same distance, larger units

What FPV latency means on an RC car

Glass-to-glass latency is the time between a photon hitting the camera and the matching pixel lighting up in the goggles. On an RC car, that delay decides how far the chassis travels before a rock, a gate, or the edge of a trail appears in the picture.

The number is a chain, not a single part. A camera needs time to expose and process a frame. A video transmitter may add almost nothing, as a typical analog VTX does, or a lot, as a digital system that encodes the picture and sometimes retransmits it can. The goggles then decode or display what arrives. Independent testers usually measure the whole chain with an LED and a high-frame-rate camera. Those end-to-end figures are what this calculator uses for the system presets.

Analog is often still the lowest-latency path when the camera and goggles are good. A typical modern stack has been measured around 20 milliseconds end to end. That is not automatic. Older or heavy wide-dynamic-range analog cameras have averaged closer to 30 to 40 milliseconds in camera-only tests, and budget box goggles can add more display delay than a module goggle with a good receiver. The analog transmitter itself is effectively instant. A setup like a typical CMOS board camera, an analog VTX, and EV800D-class goggles is the usual budget starting point; a quality module goggle is likely a little quicker than that box-goggle class.

Digital systems trade some delay for a sharper picture. In recent glass-to-glass tests, DJI O4 and Walksnail Avatar at 100 fps both landed around 28 milliseconds, DJI O3 around 30 milliseconds at 100 fps, and slower 60 fps modes climbed into the 40-millisecond range. Race or low-latency modes can come back down, to about 20 milliseconds on DJI O4 and about 23 to 24 milliseconds on Walksnail. HDZero is the outlier on the fast side: the manufacturer publishes a fixed glass-to-glass figure as low as 14.1 milliseconds, with a first-pixel figure of about 3 to 4 milliseconds, because it does not use the same compression-and-retransmit approach. Budget digital kits aimed at beginners, such as the BetaFPV P1 / ArtLynk system, have been measured around 64 to 68 milliseconds — usable on a slow crawler, less ideal at bash speeds.

These are typical figures, not a promise for a particular board, firmware, or signal condition. Digital systems that retransmit can add delay when the link gets messy. Camera choice on analog still matters a lot. Manufacturer “as low as” numbers sometimes describe only part of the pipeline. The distance result is simple physics: speed times delay. At 30 km/h, 28 milliseconds of latency is about 23 cm of travel — a reminder that a delay that feels tiny in a chair is a real gap at speed. For how to choose a first kit, see the FPV on an RC car guide.

FPV latency FAQ

What is glass-to-glass FPV latency?

Glass-to-glass latency is the time from a photon hitting the camera sensor to the matching pixel lighting up in the goggles. It includes the camera, transmitter or air unit, wireless link, receiver, and display, not just the radio hop.

How far does an RC car travel during FPV delay?

Distance equals speed times latency. At 30 km/h, 28 ms of delay is about 23 cm of travel. At crawling speeds that gap is only a few centimetres; at bash or race speeds it can be half a metre or more.

Is analog FPV lower latency than DJI or Walksnail?

A good analog setup is often still a little faster. Independent glass-to-glass tests have measured a typical analog stack around 20 ms, DJI O4 and Walksnail Avatar around 28 ms at 100 fps, and DJI O3 around 30 ms at 100 fps. HDZero publishes a faster fixed figure, as low as 14.1 ms. Budget digital kits can be much slower, around 64 to 68 ms in one test.

Does FPV latency matter on a crawler?

Usually less than on a fast basher or racer. At walking-pace trail speeds, even 40 to 60 ms of delay only moves the car a few centimetres before the picture updates. Image clarity and a solid video link often matter more than shaving milliseconds. Latency becomes important when the car is carrying speed toward an obstacle.

Why do manufacturer latency numbers differ from independent tests?

Makers sometimes quote only part of the pipeline, such as link delay, first-pixel delay, or a best-case race mode. Independent testers usually measure the full glass-to-glass chain with an LED and a high-frame-rate camera. Firmware, goggles, frame rate, and signal quality can also change the result. This calculator uses typical published figures and shows a range where tests disagree.

Can camera, VTX, and goggle delays just be added together?

Only when the numbers come from the same kind of test, or when entering a personal measurement. Camera-only and goggle-only figures from different testers often overlap or leave gaps, so they may not add up to a real glass-to-glass total. The system presets in this calculator use end-to-end measurements or manufacturer glass-to-glass figures rather than a homemade sum.

Quick presets

How to read the result

  • Lower latency is better, but speed multiplies the gap.
  • A crawler can live with a slower digital kit; a fast basher feels it sooner.
  • 60 fps modes on DJI and similar systems are usually slower than 100 fps.
  • Enter a custom total if a personal LED test is available.